The C33 is a throw-over hide, not a pegged hide
The C33 Lightweight Throw Over Hide is designed for speed: you throw it over yourself, your camera, tripod and seat to break up your shape and outline. It has no poles or pegs to worry about, and it rolls up to fit in a camera bag or rucksack. That makes it excellent for impromptu setups when you are walking or tracking, as Kevin Keatley describes developing the bag hide for deer on Exmoor.
Because the C33 ships without poles or pegs, any anchoring you add is your own modification. That is fine, but treat it as a separate job from the hide itself. The fabric is lightweight and breathable but not proofed, so it is not designed as a weatherproof shelter. Anchoring is about keeping the hide in place and preserving your outline, not about making it storm-proof.
What the C33 gives you to work with
- C33 Lightweight Throw Over Hide (bag hide): No poles or pegs are supplied with the C33 Throw Over Hide. Any ground spikes or guy lines are additions you supply and fit yourself, so plan them as part of your kit rather than expecting them in the bag.

C33 Lightweight Throw Over Hide (bag hide) - C33 Lightweight Throw Over Hide (bag hide): The hide is made from a lightweight breathable but not proofed material. It is light enough to lift in wind and not waterproof, so anchoring should focus on holding the shape and outline rather than sealing out rain.
- C33 Lightweight Throw Over Hide (bag hide): The C33 rolls up to fit in a camera bag or rucksack. Keep your anchoring hardware small and separate so the packed hide still fits your bag.
How to anchor the C33 with ground spikes
The aim is to stop the fabric lifting and flapping while keeping it loose enough to throw over your kit. Work through these steps in order.
- Set up the hide first: Throw the C33 over yourself, your camera, tripod and seat as you normally would. Get your shooting position right before you add any anchoring, because spikes will limit how much you can adjust the fabric afterwards.
- Choose spike points at the hem: Pick a few points around the lower edge of the fabric where it meets the ground. Spread them out so the hide is held evenly rather than pulled tight in one place.
- Attach the fabric to the spikes: Use short guy lines or loops of cord from the hem to the spike heads. The supplied information does not include a fixing method for the C33, so use a method that does not tear the lightweight fabric and check it holds before you rely on it.
- Push the spikes in at a low angle: Angle ground spikes away from the hide so tension pulls against the spike rather than lifting it out. The exact angle and depth depend on your ground and spike design; the supplied information does not give a recommended angle or depth.
- Leave slack for movement: Keep the lines slightly slack so the hide still drapes over you and your camera. Pulling it tight turns a soft throw-over into a rigid shape and can lift the hem.
- Test before the animal arrives: With the hide in place, check that you can still raise your camera and follow movement without pulling a spike or dragging the fabric. Adjust any point that snags.
Anchoring choices that suit a lightweight bag hide
- Use a few points, not many: The C33 is designed to be thrown over and adjusted. Every extra spike reduces your ability to shift position quietly.
- Keep hardware small: The hide packs into a camera bag or rucksack, so choose compact spikes and short cord that fit alongside it.
- Match the spike to the ground: The supplied C33 information does not specify ground types or spike sizes. Pick spikes for the soil or turf you actually shoot on, and test them before a session.
- Do not rely on the hide for weather protection: The material is breathable but not proofed. If rain is likely, anchoring will not make the C33 waterproof; plan separate protection for your camera.
When anchoring is the wrong move
The C33's main advantage is speed. If you are moving often, stalking deer, or setting up for a few minutes at a time, adding and removing ground spikes can cost you the moment. In calm conditions, throwing the hide over your kit and checking the wind direction, as Kevin did on Exmoor, may be all you need.
Anchoring makes more sense when you plan to stay in one position for a while, when the wind is lifting the hem, or when the fabric keeps shifting against your lens. In those cases a few well-placed spikes protect the outline you worked to build. The supplied information does not give a wind speed or condition threshold, so judge it by whether the hide stays put in your own setup.
C33 variants and pack weight
- C33 Lightweight Throw Over Hide (bag hide): Available in lightweight Realtree Hardwoods green at approximately 550 g, or limited availability in lightweight All Terrain Pattern at approximately 600 g. Both versions are light enough to lift in wind, so the anchoring decision applies to either pattern; the All Terrain version adds about 50 g to your pack.


